Military Headsets

  • EM-001-AP Military Headset
  • EM-001-AP2 Military Headset

EM-001-AP

$469

  • Tocnet capability
  • High fidelity utilizing 4-speaker system
  • Stereo (Dichotic) audio
  • High strength active noise reduction system
  • A noise canceling electret microphone
  • Superior comfort provided by gel ear seals and a lambs wool comfort top
  • Impedance – 300Ohm stereo
  • Effective frequency range – 80 – 18k Hz
  • Type – M65 electret noise canceling
  • Boom – Full flex type
  • Frequency Response – 300 Hz – 8k Hz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Minimum expected additional attenuation: – 19 dB
  • Nominal Current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Domes – polycarbonate or ABS
  • Headband – steel
  • Cable length – 60 inches
  • Cable type – 6 conductor; polyurethane jacket;
  • polypropylene insualtion
  • Plug – Nexus BR-107
  • Weight – 19.616 oz. without cable
Meets MIL-STD-912/PS-0276/3
  • EM-002-ACH-300-BTH Military Headset
  • EM-002-ACH-300-BTH Military Headset

EM-002-ACH-300-BTH Tactical Headset

$550 (with Talkthrough)

$499 (without Talkthrough)

TOCNET compatible – designed specifically for the TOCNET system- currently the preferred headset for use with TOCNET

Designed to fit under ACH, MICH, and PASGT type helmets.

The “TANR” series Headset (Tactical Active Noise Reduction), a clean sheet product designed specifically for use with the TOCNET communication system. Superior speech intelligibility is achieved through the use of 4 audio speakers, high strength active noise reduction, and a noise-canceling electret microphone. Comfort is emphasized. Pressure points and hot spots are minimized through the use of a thin nylon head strap and a neckband wrapped in padded cordura fabric.

  • High fidelity – excellent audio quality achieved with a 4 speaker audio system
  • Active noise cancellation – improves speech intelligibility by neutralizing low-frequency noise
  • Lightweight – 16 oz. without cord
  • Lower cost – made in USA for approximately one-half the price of competing headsets

Rugged design – modular electronics have passed all environmental tests
Full-flex boom microphone – utilizes noise-canceling electret microphone to provide maximum speech intelligibility. Boom mic connection on each earcup allows for R or L handed shooters

  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reductionCompressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – beryllium/copper spring steel
  • Cable Length – 36″
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation
  • Plug – Hirose Hr 10A
  • Weight -16 oz. (w/o cable)

Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards*

* Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

  • EM-002-ACH-300-2 Military Headset
  • EM-002-ACH-300 Military Headset

EM-002-ACH-300 Tactical Headset

$550 (with Talkthrough)

$499 (without Talkthrough)

TOCNET compatible – designed specifically for the TOCNET system- currently the preferred headset for use with TOCNET

Designed to fit under ACH, MICH, and PASGT type helmets.

The “TANR” series Headset (Tactical Active Noise Reduction), a clean sheet product designed specifically for use with the TOCNET communication system. Superior speech intelligibility is achieved through the use of 4 audio speakers, high strength active noise reduction, and a noise cancelling electret microphone. Comfort is emphasized. Pressure points and hot spots are minimized through the use of a thin steel headband padded with tempur foam and wrapped in cordura fabric.

  • High fidelity – excellent audio quality achieved with a 4 speaker audio system
  • Active noise cancellation – improves speech intelligibility by neutralizing low frequency noise
  • Lightweight – 16 oz. without cord
  • Lower cost – made in USA for approximately one-half the price of competing headsets

Rugged design – modular electronics have passed all environmental tests
Full-flex boom microphone – utilizes noise cancelling electret microphone to provide maximum speech intelligibility. Boom mic connection on each earcup allows for R or L handed shooters

  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reductionCompressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – beryllium/copper spring steel
  • Cable Length – 36″
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation
  • Plug – Hirose Hr 10A
  • Weight -16 oz. (w/o cable)

Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards*

* Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

  • EM-001-A-M65A-HR-5K-2 Military Headset
  • EM-001-A-M65A-HR-5K Military Headset

EM-001-A-M65A-HR-5K

$540

TOCNET compatible – designed specifically for the TOCNET system- currently the preferred headset for use with TOCNET

Designed to fit under ACH, MICH, and PASGT type helmets.

The “TANR” series Headset (Tactical Active Noise Reduction), a clean sheet product designed specifically for use with the TOCNET communication system. Superior speech intelligibility is achieved through the use of 4 audio speakers, high strength active noise reduction, and a noise cancelling electret microphone. Comfort is emphasized. Pressure points and hot spots are minimized through the use of a thin steel headband padded with tempur foam and wrapped in cordura fabric.

  • High fidelity – excellent audio quality achieved with a 4 speaker audio system
  • Active noise cancellation – improves speech intelligibility by neutralizing low frequency noise
  • Lightweight – 16 oz. without cord
  • Lower cost – made in USA for approximately one-half the price of competing headsets

Rugged design – modular electronics have passed all environmental tests
Full-flex boom microphone – utilizes noise cancelling electret microphone to provide maximum speech intelligibility. Boom mic connection on each earcup allows for R or L handed shooters

  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reductionCompressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – beryllium/copper spring steel
  • Cable Length – 36″
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation
  • Plug – Hirose Hr 10A
  • Weight -16 oz. (w/o cable)

Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards*

* Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

  • GDH military headset

EM-001-H

$1,725 – $1,875

The EM-001-H-BC-P headset is a tactical style headset designed for use exclusively with the Tocnet system. The headset features the Headsets Incorporated active noise reduction system for quiet, precise communications. The talk through system provides for situational awareness while wearing the headset. The headset can be used with the foot PTT switch or separate from it. The lightweight design, gel ear seals, lightweight head strap and nape pad provide long-wearing comfort with or without a helmet.
  • Tactical designed ear cups
  • Milspec ribbon headband with Velcro hook and loop adjustments
  • Gel ear seals
  • Electret Microphone for clear communications that can be use right or left mounted
  • Headsets Incorporated Active Noise Reduction System
  • Headsets Incorporated Talk-through system
  • ANR On/Off button
  • Talk-through On/Off/Volume control switch
  • Dual Ambient sound sensing Microphones
  • Mil-spec quality cabling
  • Cable mounted PTT switch with 3 position switch for intercom or radio communication
  • Rugged Amphenol connectors for precise connections
  • Rugged foot PTT switch with a selector switch for radio or intercom operation
  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reduction-Compressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – Mil-spec polyester ribbon used with spring steel nape band for tension
  • Cable Length – 90″ stright and coiled cable combined.
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation, 10 conductor coiled cable with polyurethane jacket
  • Plug – Amphenol AP series on headset straight cable and Amphenol 13 pin on coiled cable
  • Weight -16 oz. (w/o cable)
  • Foot PTT switch assy- ruggedized foot switch with selector switch for radio/intercom usage. Has a 108″ cable to interconnect with the Tocnet jackbox and a 13 pin female Amphenol connector interface to connect to the headset.
Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards* * Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

The EM-002-H-BA-P headset is a tactical style headset designed for use exclusively with the Tocnet system. The headset features the Headsets Incorporated active noise reduction system for quiet, precise communications. The talk through system provides for situational awareness while wearing the headset. The headset can be used with the foot PTT switch or separate from it. The lightweight design, gel ear seals, lightweight head strap and nape pad provide long wearing comfort with or without helmet.

  • Tactical designed ear cups
  • Milspec ribbon headband with Velcro hook and loop adjustments
  • Gel ear seals
  • Electret Microphone for clear communications that can be use right or left mounted
  • Headsets Incorporated Active Noise Reduction System
  • Headsets Incorporated Talk-through system
  • ANR On/Off button
  • Talk-through On/Off/Volume control switch
  • Dual Ambient sound sensing Microphones
  • Mil-spec quality cabling
  • Cable mounted PTT switch with 3 position switch for intercom or radio communication
  • Rugged Amphenol connectors for precise connections
  • Rugged foot PTT switch with a selector switch for radio or intercom operation
  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reduction-Compressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – Mil-spec polyester ribbon used with spring steel nape band for tension
  • Cable Length – 90″ straight and coiled cable combined.
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation, 10 conductor coiled cable with polyurethane jacket
  • Plug – Amphenol AP series on headset straight cable and Amphenol 13 pin on coiled cable
  • Weight -16 oz. (w/o cable)
  • Foot PTT switch assy- ruggedized footswitch with a selector switch for radio/intercom usage. Has a 108″ cable to interconnect with the Tocnet jackbox and a 13 pin female Amphenol connector interface to connect to the headset.

Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards*

* Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

The EM-001-H-BC-P-F headset is a tactical style headset designed for use exclusively with the Tocnet system. The headset features the Headsets Incorporated active noise reduction system for quiet, precise communications. The talk through system provides for situational awareness while wearing the headset. The headset can be used with the foot PTT switch or separate from it. The lightweight design, gel ear seals, lightweight head strap and nape pad provide long wearing comfort with or without helmet.
  • Tactical designed ear cups
  • Milspec ribbon headband with Velcro hook and loop adjustments
  • Gel ear seals
  • Electret Microphone for clear communications that can be use right or left mounted
  • Headsets Incorporated Active Noise reduction System
  • Headsets Incorporated Talk-through system
  • ANR On/Off button
  • Talk-through On/Off/Volume control switch
  • Dual Ambient sound sensing Microphones
  • Mil-spec quality cabling
  • Cable mounted PTT switch with 3 position switch for intercom or radio communication
  • Rugged Amphenol connectors for precise connections
  • Rugged foot PTT switch with a selector switch for radio or intercom operation
  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reduction-Compressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – Mil-spec polyester ribbon used with spring steel nape band for tension
  • Cable Length – 90″ straight and coiled cable combined.
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation, 10 conductor coiled cable with polyurethane jacket
  • Plug – Amphenol AP series on headset straight cable and Amphenol 13 pin on coiled cable
  • Weight -16 oz. (w/o cable)
  • Foot PTT switch assy- ruggedized footswitch with a selector switch for radio/intercom usage. Has a 108″ cable to interconnect with the Tocnet jackbox and a 13 pin female Amphenol connector interface to connect to the headset.

Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards*

* Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

The EM-002-H-BA-P-F headset is a tactical style headset designed for use exclusively with the Tocnet system. The headset features the Headsets Incorporated active noise reduction system for quiet, precise communications. The talk through system provides for situational awareness while wearing the headset. The headset can be used with the foot PTT switch or separate from it. The lightweight design, gel ear seals, lightweight head strap and nape pad provide long wearing comfort with or without helmet.
  • Tactical designed ear cups
  • Milspec ribbon headband with Velcro hook and loop adjustments
  • Gel ear seals
  • Electret Microphone for clear communications that can be use right or left mounted
  • Headsets Incorporated Active Noise Reduction System
  • Headsets Incorporated Talk-through system
  • ANR On/Off button
  • Talk-through On/Off/Volume control switch
  • Dual Ambient sound sensing Microphones
  • Mil-spec quality cabling
  • Cable mounted PTT switch with 3 position switch for intercom or radio communication
  • Rugged Amphenol connectors for precise connections
  • Rugged foot PTT switch with selector switch for radio or intercom operation
  • Impedance – 300 ohm stereo
  • Effective Frequency Range – 80 – 18k Hz
  • Boom Microphone Type – M65 electret noise canceling
  • Boom – Full flex type; R/L interchangeable
  • Frequency Response – 300Hz – 8kHz
  • Source Resistance – 220 – 2200 ohms
  • ANR effective frequency range – 80 – 600 Hz
  • Maximum expected additional attenuation – 19dB
  • Nominal current – 32 mA
  • Voltage 12.0 – 18.0 VDC at the plug
  • Binaural function integrated with active noise reduction-Compressor/limiter – limits binaural audio to 82db at ear
  • Current draw – 30mA
  • Source voltage – 9v
  • Domes – polycarbonate or ABS
  • Headband – Mil-spec polyester ribbon used with spring steel nape band for tension
  • Cable Length – 90″ straight and coiled cable combined.
  • Cable type – 6 conductor; polyurethane jacket; polypropylene insulation, 10 conductor coiled cable with polyurethane jacket
  • Plug – Amphenol AP series on headset straight cable and Amphenol 13 pin on coiled cable
  • Weight -16 oz. (w/o cable)
  • Foot PTT switch assy- ruggedized foot switch with a selector switch for radio/intercom usage. Has a 108″ cable to interconnect with the Tocnet jackbox and a 13 pin female Amphenol connector interface to connect to the headset.

Noise canceling/audio modules meet Gentex Corp. PS-0276 environmental standards*

* Per Gentex report dated 6-17-03

Meets MIL-STD-912/PS-0276/3*

* Per Gentex report dated 6-17-03

Call Us Today for Pricing